Posted by & filed under Scott's Plumbing Tips!, Uncategorized

Drain and pipe clogs are the bane of sinks and bathtubs everywhere, and they can be infuriating to deal with. While some are easy enough to clear out with hot water, or with basic plumbing devices like snakes, some are simply too large, too thick, or too compacted to be easily removed. In these situations, the best option is often to hire professional hydro jetting services to handle the clog.

Hydro jetting isn’t something you can do yourself, as it requires specialized equipment. It’s also typically used as a last resort for clogs that can’t be cleared in other ways. Still, hydro jetting services can work wonders, and are particularly useful for commercial plumbing, such as clearing restaurant sink drains.

In this article, we’ll go over everything you should know about hydro jetting services, so you can make an informed choice the next time you have a stubborn clog.

I. What Is Hydro Jetting?
Simply put, hydro jetting involves spraying extremely high-pressure water into pipes as a way of clearing out particularly bad clogs.

This requires specialized equipment capable of putting out far more water than you’d get from home plumbing, or even in a commercial setup. Professional hydro jets can output over 20 gallons of water per minute, at an overall pressure of 5,000 psi or even higher. That’s strong enough to quickly tear through even the largest and toughest clogs!

So why are more and more plumbers choosing to offer hydro jetting services? Because in many cases, it’s more effective at clearing out these clogs.

II. Hydro Jetting vs Snaking
The most common professional tool for clearing clogs is the plumbing snake. This is a flexible hose with a hook or small drill at the end, which is pushed through the pipes until it connects with the clog. Then the snake is worked to dig through the clog, break it up, and allow water to flow through again.
However, snakes have a couple of disadvantages. First, they have limited length. Plumbing snakes are typically between 20-50 feet long, which is fine for most home plumbing, but if the clog is further down than that the snake is useless.

Also, the clog cannot be too large, or else the snake simply won’t be able to penetrate it effectively. The snake would just dig material off the top, which would get re-compacted the next time water is poured through.

III. Hydro Jetting vs Chemical Decloggers
The other popular solution – unfortunately – for clearing clogs is using chemical agents to break down the clog. Homeowners like this solution, since it promises a quick and easy fix – pour a bottle of acid into the drain, wait awhile, and hope it’s dissolved the clog.

However, chemical agents can still only work by making direct contact with the material in the clog. A thick clog might see its top layer dissolve but would be otherwise unmoved.

Also, chemical decloggers are bad for your pipes in the long run. While using them occasionally won’t cause any major problems, each time you do, it’s going to eat away at your pipes just a little. Over time, with too many chemical treatments, it can start to break down the pipe. This is particularly true if you have plastic pipes, which are very vulnerable to damage.

We recommend avoiding chemical agents whenever possible, for this reason.
In short, water jetting services can clear out tough clogs that other methods cannot fix. However, that doesn’t mean that water jetting is always going to be the right solution.

IV. When Hydro Jetting Services Shouldn’t Be Used
Hydro jetting isn’t a magic fix-all, and there are situations where a good plumber wouldn’t recommend it.

First, as mentioned above, hydro jetting isn’t ever going to be the first choice for clearing a clog. Jetting is typically reserved for situations where other methods have been tried, like snaking, or if the clog has been identified as being too deep into the pipe for other methods.

There is also a potential risk to the pipes if the hydro jetting is being done by someone who is poorly trained. A good plumber will carefully survey the pipes before using hydro jetting to make sure there’s no chance of damage.

Another issue would be if the clog is caused by a break in the pipe, such as a tree root intruding into the plumbing system. If the pipe is broken, hydro jetting would only cause the break to get worse, without fixing anything.

V. Hydro Jetting Services for Commercial Businesses
Hydro jetting can be particularly valuable for businesses that make extensive use of their plumbing, such as restaurants and other commercial kitchens. These operations are prone to clogs in the first place since a lot of oil, grease, and other debris will be constantly going into the pipes. This can lead to extremely large, difficult-to-clear clogs which call for hydro jetting. Plus, commercial pipes are typically thicker and more sturdy than residential, so they’re likely to be able to stand up to the pressure.

Hydro jetting can be a particularly effective way of clearing out grease traps in commercial kitchens. Grease is sticky and hard to deal with using other drain-cleaning methods. However, in some cases, a neglected grease trap may be so clogged up that it needs to be cleared manually before hydro jetting would be effective.